My Ice Maker Not Making Ice But Water Works?

Ice Maker Needs Repair

 

 

My Ice Maker Not Making Ice But Water Works?

You may find that your Whirlpool refrigerator won’t make ice, but the water is working fine, for a number of reasons. In other cases, the fact that the Whirlpool ice maker is not producing ice may be due to insufficient water supply. If you find ice cubes inside the mold, your ice maker is filling with water, and the water supply may not be the problem. Water may not enter the built-in ice maker due to frozen lines, a missing filter, or a closed water supply valve.

Ice makers receive water through a small plumbing pipe that runs from the refrigerator to a water pipe, funnel, or water filter. The small one leads to the water fill valve in the refrigerator, which is controlled by the ice makers’s thermostat. Refrigerators connected to the water supply will also have at least one filling valve inside. The fill pipe supplying water to the ice maker in the refrigerator may freeze and prevent water from entering the ice maker.

The water for the ice maker comes to the refrigerator from the main power line to the house, and a blockage in the valve that allows water to enter the refrigerator can prevent the machine from making ice. There is only one plumbing connected to your refrigerator; however, the refrigerator has two plastic water pipes that run from the dual water valve to the refrigerator’s ice maker and water dispenser. The valve on the water lines may not be open enough to get enough water into the refrigerator.

Make sure the water line is not kinked behind or under the refrigerator (it’s better to use 1/4″ copper tubing rather than plastic tubing to prevent kinks). To clear a frozen waterline, you will need to thaw the ice from the inside. Restore power to the refrigerator and wait for the water supply to fill the mold.

Manually remove any remaining ice from the mold by adding a little water and letting it rest for one minute. Hot water will melt stuck ice chunks without adding chemicals to the ice maker tray, making it safe to immediately resume ice making in the ice maker assembly. Some warm water (with a towel ready to clean) will melt any ice jams.

When this cloudy water remains on the ejector arm and builds up over time, it can cause the ice machine to jam, preventing new ice from falling. Sometimes the water fills the tray too much and the water freezes around where the ice cubes form before they fall into the ice container.

This could be due to old ice getting stuck in the molds, or just pieces of ice so that the ice comes out broken or incomplete. A blockage in the line or a closed valve can easily explain a sudden shortage of ice if new ice cannot be made. If a lot of ice freezes, new ice cannot form and the waterline can also be a problem because it cannot fill the sample.

If the plumbing is clogged, water cannot come out and ice does not form. Since the water must pass through the filter, when it is filled with dirt, no water can pass through. A clogged water filter, a kinked water hose, or a faulty inlet valve can restrict water flow to the ice maker.

The location of the water inlet valve varies by manufacturer, but the water inlet valves on Kenmore and Whirlpool ice makers are usually located behind the refrigerator. Find the water supply stopcock behind the refrigerator or under the sink, close it, unscrew the copper pipe from the back of the refrigerator, put the copper pipe into a bucket, open the faucet and see if water is leaking.

If the ice maker is not producing ice, but you see the ice ejector lever move and a buzzing sound is heard for about 10 seconds, the water valve is calling for water that is not coming out. The water fill valve opens for a few seconds to fill the ice mold and the cycle repeats. The ice maker thermostat then turns on the small ice maker motor, which turns the ice ejector lever.

Freezing of ice on the probe or movement of the paddle signals to the ice maker in the refrigerator that the ice must stop. When the refrigerator is turned off, it gradually heats up and melts all the ice anywhere along the waterline. After all, anything that is filtered by tap water before it turns to ice will eventually clog the filter.

Even if the temperature in the refrigerator is well below freezing, the water molecules condense again and freeze together where the cubes meet. A Whirlpool side-by-side refrigerator that won’t freeze after a power outage needs some detective work. That’s why, if you find that your Whirlpool French door refrigerator isn’t making ice, you need to fix the problem quickly before the warmer days come.

A loose drain plug can leave you with thin ice as water drips from the water tray. A faulty faucet valve—the small device that connects the ice makers’s water supply hose to the water hose from the ice makers’s water supply hose to the water hose—may cause a problem where the ice makers’s water supply hose connects to the water hose.

Depending on the design of your refrigerator, the water supply pressure may be sufficient to supply water to the ice maker, but not enough to supply water every time you try to draw water from the water dispenser. When using plumbing cleaning kits, carefully fill the plumbing with warm water to melt the ice.
To schedule ice maker repairs in Oklahoma City contact Appliance Repair OKC Services by calling 405-378-4566 or visit our website at https://www.okcappliance.com to also our Google business page at https://cutt.ly/YEnc8qk. Call now!

 

The post My Ice Maker Not Making Ice But Water Works? appeared first on Appliance Repair OKC Services | Best Appliance, Washing Machine Repair Company in Oklahoma.