My Washer Won’t Drain or Spin Correctly?

Technician checking washing machine with digital multimeter in kitchen

 

 

My Washer Won’t Drain Or Spin Correctly?

If your clothes are still sitting in water after your washing cycle is over, your washing machine probably has a drainage problem. If you put the washer too far off the ground, the machine might not be able to push the water out, or might drain very slowly.

A clogged drainage trap may be a common, non-mechanical cause of front-loading washing machines that do not seem to be spinning. Problems in the home water supply can make the front-loading appliance very slow to drain, or drain at all. If a clog occurs in a home drainage pipe, then the washing machine cannot drain while everything else is working properly. Check the washer is level, then adjust feet accordingly so that your washer does not shake or shift, which could be the reason for drainage problems.

Open up the machine and shift items to balance the washing machine load, and the washing machine will be more effective at spinning. If your washing machines drive belt is broken or falls off of its wheels, your washer can still be agitated and produce sound, but the rotors do not turn. If a latch is broken or a switch is bad, the machine will not get a signal to run, and the machine will not spin, empty, or even begin.

If the lid switch assembly is defective, the Bosch washing machine will not spin and drain, even when you correctly lock the door. So, examine the tab on the lid, which strikes the failed lid switch; if it is broken, your washer might halt mid-drain cycle. Telling may mean a loose or cracked lid switch is keeping the washer from draining when it should. If your washer is filled with water, but is not stirring, it is probably because of a bad lid switch, broken belt, or motor issue.

If you go inside the washer expecting to move the damp clothes into the dryer, only to find that your clothes are soaking wet, with water still sitting at the bottom of the tank, the machine is not draining properly. When all of the water has been flushed and the drained spool is spinning very quickly, it is equivalent to pulling out your clothes before putting them in the dryer. The spinning of the washers drum is also the way the water is eventually spun off of the clothes, so they come into the dryer not completely soaked. The belt on the washer is attached to the machinery on the bottom of the drum, and the spin on the belt moves the drum back and forth either to stir, or around rapidly so the clothes are eventually drained.

Sometimes socks or other small articles of clothing find their way down the washing machine exhaust pipe, and they can also get as far as the exhaust pump. It is very common for small socks or other small articles of clothing to find their way into your water drainage system, clogging up a hose leading to your pump, or the pump itself. Sometimes, small pieces of clothing or trash may get to a washing machines drainage pump and block its impeller.

Coins and other small objects can become caught in the pump or other parts of your washing machine, causing drainage difficulties. Small items – such as pennies, keys, buttons, or clothes clips – may drop from pockets and clothes, and thus get caught by the hose connecting your washer to the drainage pump. Clogs sometimes occur after washing items such as carpets, which may have shedding fabric fibers, or when clogging occurs with a coiled hose.

If the water is successfully flushed from your washing machine, but it is then spilling from your sinks drainage pipe, or backing up into your washing tub, the issue is probably a conventional clog. If you can hear the washing machine pump working, but there is no water coming out of your washer, then the likely issue is a clog in the rubber drain pipe running from the rear of your machine to a drain stand pipe or in your washing machines wash tub. The hose carrying water from the back of your machine the back of the machine may be causing it to drain incorrectly. If your washing machine is backed up within just a few seconds, the blockage is probably fairly tight, and it could be cleared by using a small powered snake working through your tubings drainage header.

Position yourself so that you can see the drain standpipe, but also still be able to reach the flush. Shake out the drain pipe, and then put your washer back into position, making sure that your drain pipe is not bent or pinching. Then, plug the drain hose into your machine, power it back on, and start your wash cycle to make sure it is draining correctly. If it takes some time for your drainage pipe to fill, the blockage is somewhere along the drainage pipe, possibly past the drainage trap.

The clog or blockage prevents the water from flowing freely down the pipe during draining, which causes the back-up in your Bosch washing machine. If a door latch is faulty, it will not send the signal to the door switch, and your washer cannot run, drain, or spin. If a door lock or slammer is malfunctioning, it will likely show a digital error code and the washer will stop stirring and rotating. As a result, the washer will not achieve an appropriate spin rate, leaving your clothes dripping wet by the end of the cycle.

A torn drive belt, or one that has fallen off a pulley wheel, may result in agitation in your washing machine throughout the washing cycle, but – despite the motors running noise – your Drum stays stationary throughout the spin cycle.

To schedule washing machine repairs in Oklahoma City contact Appliance Repair OKC Services by calling 405-378-4566 or you can visit our website at https://www.okcappliance.com. Also our Google business website can be found at https://cutt.ly/YEnc8qk. Call now!

 

The post My Washer Won’t Drain or Spin Correctly? appeared first on Appliance Repair OKC Services | Best Appliance, Washing Machine Repair Company in Oklahoma.