Cooktop Creates Sparks When Turned On?

Young Woman Looking At Male Repairman Examining Oven In Kitchen

 

 

Cooktop Creates Sparks When Turned On?

If a burner element in an electric cooktop surface coil is igniting, you know. On gas stoves, you would expect to see a little sparking when you turn on, but with an electric stove, a spark is just bad news for you whenever you see one.

When your gas stove keeps clicking, it is because a sparking electrode keeps trying to spark the gas, even though there is no need. If each burner keeps clicking, the problem is likely any of the above, not the spark electrode. While it is very common to have more than one burner begin clicking while you are lighting the stove, that does not necessarily mean that you have to change out each and every spark electrode in the stove.

Turning the electricity off to the gas stove, either by pulling the plug or turning the switch in your electric box (breaker), should stop the clicking, since the spark electrodes cannot spark without electrical current. If fluid has entered the switch, you should disconnect power to the gas stove and allow the switch to dry.

If the switch continues to spark, you can test the switch with a multimeter to see if the switch is damaged beyond repair and needs replacement. You can check each switch individually to see if one needs replacement. If you are not sure whether an ignition switch or spark module is causing the clicking noise, the ignition switches can be disconnected from the spark modules to identify the responsible part.

If the faulty spark ignition switch fails at electrical contact closure, it will transmit a constant voltage to the spark module, which causes consistent clicking. When you open the cooking pot handle to turn the burners on, the spark ignition switch is closed so that voltage can be sent to the spark module. The ignition in your stove is controlled by an ignition switch, which tells the burner it is time to ignite, and the spark module, which is the part that produces the actual spark.

A typical spark module will click as many as three times before sparking and lighting up your stove. If you feel the click coming from your stove, and you look closely, you might notice it is sparking consistently too. You also will want to turn off your sparking burners immediately when you notice that the sparking is happening in an electric stove.

Typically, Sparking is a rarer issue, but it does happen, and there are several causes you will want to fix before trying to use your stove again. Whether your burners are clicking and not turning on, or they will not stop clicking even after they are turned off, this issue could be caused by defective parts.

Like many problems with your burners, the accumulation of fats and food particles may be the reason why the burners begin clicking. Liquids from cleaning and cooking may be getting in your stove, and are causing your burner to make that clicking noise all the time. You can often detect causes before the popping happens by checking if the burners are wobbling as you take and put them back in for cleaning.

What happens when your burners begin to spark because of loose connections is the higher resistance causes the entire thing to heat up. When those connections get loose, your burners start to spark because of high resistance. Use may result in higher resistance, which may cause it to get too hot and begin burning wires, or it may result in an arc, which is what you are seeing with sparks.

In extreme cases, sparking elements may blow out a circuit board, making repairs harder and harder. Ticking is quite a common issue, especially in ranges with spark-ignition systems. If your burners are clean and dry, and your ignition switches are working properly, then the likely culprit is the sparking component being faulty, causing ticking.

If a switch is faulty, this can result in an ongoing power supply to the spark module, which would result in a continuous click from the spark module. The spark switch starts ignition by sending electrical current to the spark module. These switches are controlled with a knob which, when turned to light, closes the switch, which allows voltage to flow to the spark module, which routes it to an electrode which produces the spark. When we push on either gas knob, we apply pressure on the button that will close the electrical contacts, thus, sparks are generated and corresponding flames are lit.

It is common that when the knob is depressed and rotated, the sparks, or clicking, occur simultaneously for all surface burners with natural gas. When the knob is turned and the burner is engaged, it will produce an electrical spark in order to ignite the mixture of air and gas flowing out the burning head in order to produce flame. The spark electrode ignition device, also called a surface burner ignition device, is located near the burn head at the top of the cooktop. Grease, water from spilled pans, or even the extra damp sponge used when cleaning up your stovetop area could get your spark electrode igniter wet, causing it to continuously spark.

Like the spark electrode igniter, water can get to the spark igniter too, whether it is through cleaning the stovetop handle, or spilling from boiling pots over the top of the stove. The spark switches may get shorted by the presence of water, electrical surges, or a variety of other reasons.

If it appears there is no evidence of damage, and the element continues to spark even after being connected to another outlet in your cooker, then it is likely to be faulty and needs replacing. The spark module can be tested for continuity using a multimeter to determine whether or not it is faulty.

Not only does that constant click become really annoying really fast, but having the gas burner on the stove keep clicking is going to wear down the igniter a lot quicker as well.

If you are having oven issues and need oven repair in Oklahoma City contact Appliance Repair OKC Services by calling 405-378-4566 or visit our website at https://www.okcappliance.com. Alternatively you can also visit our Google business website at https://cutt.ly/YEnc8qk.

 

The post Cooktop Creates Sparks When Turned On? appeared first on Appliance Repair OKC Services | Best Appliance, Washing Machine Repair Company in Oklahoma.