My Ice Maker Has Stopped Making Ice?
A number of factors could cause your ice maker to malfunction in your freezer, so you will want to figure out what is behind the problem so that you can quickly solve it. Some ice maker issues may eventually cause bigger (and costlier) problems with your fridge or freezer, so it is important that you find a fix ASAP so everything is working correctly.
If you tried these ice maker repair tips and the ice maker is still not working, plug the fridge back in and use Appliance Repair OKC Services for refrigerator repairs. While the savvy home owner may be able to perform these repairs and replacements on their own, those who are uncomfortable or unfamiliar with this process should consider calling in professional appliance repair services when their ice maker is not working.
Whether your refrigerators ice maker is broken, or your freezer has a shivering problem, problems with your kitchen appliances may best be left to the professionals – particularly those with no experience in plumbing, electrics, or other types of repairs. Some GE fridges have a sensor or a timer that stops the ice maker from working if you need to change your water filter. A clogged water filter may limit water flowing to the ice and water dispensers, preventing the ice maker from working correctly. If a water intake valve is defective or does not receive sufficient pressure, then the ice maker cannot function correctly.
While you have access to the water inlet valve and the water supply lines, it is good to test water pressure, which is also a common source of problems with the ice maker. The water inlet valve may be defective if it becomes blocked by mineral deposits, preventing the valve from opening. If the water inlet valve has adequate pressure and is receiving power, but the ice maker is not filling up with water to produce ice, then the water inlet valve needs to be replaced.
If there is more than just ice on top of the ice makers fill pipe, you may have a large amount of home water pressure needed to ensure that the water flows to the ice maker, or you may have mud or defects on the water inlet valve. If your ice maker is not producing ice, or the ice is small or misshaped, a water fill tube could be a problem. There may be a few reasons why your ice maker is not making enough ice, including a lack of water pressure or a bend in your water supply lines.
If my ice maker is just not working – meaning no ice is sitting in trays – problems with the flow of water might be the cause. A blockage, leak, or damage to a water supply line can make your ice maker shut down automatically or otherwise stop working. If your ice maker uses water lines (directed water), be sure the water is flowing freely and water is reaching the handheld ice maker.
The water line can be checked at where the water supply line goes into the back of your cooler and at the point it goes into your ice maker within your cooler. Locate the water shutoff valve behind the refrigerator or below the sink, shut it off, unscrew the copper supply line from behind the refrigerator, place the copper supply line into a bucket, open the valve, and see if any water comes out. To clean blocked pipes, apply a little heat with a hairdryer or using the steam from a warm cup of water.
The water refill valve is turned on for several seconds to refill the ice mold again, and the cycle repeats. Once the mold has reached a suitable temperature, the ice maker dumps out ice and fills up the mold again with water. If the ice maker is not producing ice, but you see the ice-ejection arm move, and you hear a whirring sound for around 10 seconds, then the water valve is asking for water, which is not coming.
If your thermostat is set to very low, your whole ice maker can take an impact, freezing the water before it gets to the molds to create the ice. When the room is too hot, ice melts down into smaller chunks. Warm water melts away any ice bits that are trapped, and does not add chemicals to your ice mold trays — making it safer for you to start making ice again right in your mold build.
If your ice makers tray or bin has frozen, depending on the severity of ice accumulation, you may have to defrost your entire cooler, remove your ice makers components so they can defrost, or apply low-temperature heat with a hairdryer on affected components. Depending on where ice blockage or freezing has occurred, you may be able to use a dishcloth soaked in warm water, a blow dryer, defrost feature, or defrost tool to resolve the problem.
If your refrigerator has an ice ejector that is not ejecting, this may be one of a few things. In some cases, a fridge might even be designed to stop dispensing ice or water once a filter is past its replacement date, which can make it appear as though your refrigerators ice machine is broken. If a whole load of ice gets stuck, there is no way new ice will be formed. The water line can also become a problem, as it cannot be filled up.
If you are still getting ice chunks, but they are not nearly as big as they were, then it is possible that your line is at an early freeze-up phase. This could be due to older ice getting stuck to the jig, or simply chunks of ice, which is why ice is coming out broken or not complete. Or lines are having things naughty coming from a blockage, and the ice you end up with might not taste good. A line clog or closed valve can easily cause an unexpected ice shortage, as long as there is no way to produce any fresh ice.
To schedule ice maker repairs in Oklahoma City contact Appliance Repair OKC Services by calling 405-378-4566 or visit our website at https://www.okcappliance.com to also our Google business page at https://cutt.ly/YEnc8qk. Call now!
The post My Ice Maker Has Stopped Making Ice? appeared first on Appliance Repair OKC Services | Best Appliance, Washing Machine Repair Company in Oklahoma.